Sew a Cell Phone Case

  • 01 of 07

    Gather Your Materials

    An assortment of finished cell phone cases
    Debbie Colgrove, Licensed to About.com

    Sewing your own cell phone case allows you to have strength and security that you know you can count on to protect your cell phone. Make your cases out of fabric to match a purse or outfit, to express individualism, or embroider plain fabric for an even more personalized touch. This case was designed for Verizon LG VX4500 a basic flip style phone.

    Materials

    • 22" by approximately 8" scrap of fabric
    • Fusible web - approximate 11" by 8"
    • Piping to compliment your fabric choice
    • Double fold...MORE bias tape to compliment your fabric choice.
    • 6" of 3/4" to 1" wide polyester or nylon gross grain ribbon, or webbing
    • Strong reliable snaps (such as the SnapSetter™ Tool and snaps from The Snap Source, Inc)
    • Hook & Loop Tape -- 1 1/2" of 3/4"-1" wide (the wider the hook & loop tape, the stronger your closure will be)
    • Print out of the pattern
    Continue to 2 of 7 below.
  • 02 of 07

    Extend the Pattern Printout

    Photo of pattern being extended as described on the free pattern
    Debbie Colgrove, Licensed to About.com


    Extend body pattern piece as described in the pattern.

    Continue to 3 of 7 below.
  • 03 of 07

    Fuse & Cut the Fabric

    Photo of pattern cutting layout
    Debbie Colgrove, Licensed to About.com
    • Fold the fabric in half with the wrong sides together. Sandwich the fusible web between the fabrics, placing the web all the way to the fold.
    • Fuse the layers together following the directions provided with the fusible web you are using.
    • Place straight edges of the pattern pieces on the folded edge.
    • Cut one of the main pattern piece and two side pieces.
    Continue to 4 of 7 below.
  • 04 of 07

    The Back Strap

    Photo of attaching the back strap
    Debbie Colgrove, Licensed to About.com
    • Using a lighter or flame, carefully melt the ends of the webbing or gross grain ribbon to prevent the ends from fraying.
    • Fold the webbing or gross grain ribbon in thirds.
    • Attach your snaps to the strip.
    • Place the center third, 5 1/4" up from the bottom straight edge of the fabric. Stitch a rectangle around the center third of the webbing or gross grain ribbon.
    Continue to 5 of 7 below.
  • 05 of 07

    Attach the Hook & Loop Tape and the Piping

    Photo of Hook & loop tape and Piping attached
    Debbie Colgrove, Licensed to About.com
    • Attach hook & loop tape. Place the hook section across the flap edge on the opposite side from the webbing. Trim to fit the rounded area and sew on the outer edges.
    • Place the loop section in the center of the body at the straight edge, on the same side as the webbing.
    • On the same side that you attached the ribbon, apply piping to the long straight edges of the body fabric. Use a 1/4" seam.
    Continue to 6 of 7 below.
  • 06 of 07

    Attaching the Case Sides

    Attaching the case sides
    Debbie Colgrove, Licensed to About.com
    • Starting at a straight edge of the main body piece. Place a side piece under a piping edge.
    • Stitch on the piping attachment stitching line. As you approach the curve of the side piece, stop and snip the seam allowance of the body piece.
    • Continue attaching the side to the body until you reach the end of the side piece.
    • Repeat for the second side.
    • Note: It may be necessary to trim the top edge of the flap to meet the side piece if you haven't stayed perfectly on the allowed seam allowance. This...MORE does not affect the way the case fits but trim to create a smooth edge for attaching the bias tape.
    • Press the seams in on the side seam. This will add strength to the sides of the case.
    Continue to 7 of 7 below.
  • 07 of 07

    Attach the Bias Tape

    Attach the bias tape
    Debbie Colgrove, Licensed to About.com
    • Apply bias tape to the top edge of the case, turning under the last overlapping section to enclose all raw edges. You may need to hand baste the bias tape in place on this project due to the small tight corners.