01 of 08
Materials to Sew a Custom Ironing Board Cover
Sewing your ironing board cover with this free pattern will guide you through creating a custom ironing board cover that will fit your ironing board and be better than any ironing board cover you can buy even if you could find one to fit correctly. Odd shaped and older ironing boards are not a problem because you will be making a pattern that is custom made for your ironing board.
Continue to 2 of 8 below.
- You'll need a pattern making material. That can be a newspaper, tissue paper, pattern tracing grid, gift wrap, or similar materials. The material will need to be larger than the top of your ironing board. for pattern making ( Tips and Tricks to Alter, Trace and Use a Multiple Sized Pattern has more information about pattern tracing materials.)
- A pen, pencil or marker
- A ruler
- You'll need fabric. The amount will depend on the size of the pattern piece you will make in the next step. The fabric you choose should be colorfast to prevent any color transfer when using steam. You will also want an additional layer of utility fabric suck as unbleached muslin. This helps prevent fibers and fuzz from the padding from working its way onto the fabric you are pressing.
- You'll need batting. The padding of the previous ironing board cover can be reused but adding a bit of additional padding is advised. If it is necessary to replace all of the paddings, or the padding does not have any silver or reflective qualities, visit a fabric store to find a reflective fabric such as Insul-Bright
- You'll need cording such as drapery cord. (Enough to go around the edge of the ironing board and a bit more to have enough to tie it.)
- Safety Pin
- This one's optional. You'll need a toggle to hold the cord in place.
02 of 08
Make the Pattern Piece
Continue to 3 of 8 below.
- Lay the ironing board face down on the pattern material (newspaper or anything you can write on that is larger than the top of the ironing board)
- Trace the outline of the edge of the ironing board.
- Measure the thickness of the ironing board.
- Add 2" (or more if you want the cover to wrap further around the ironing board bottom) to the thickness measurement. This measurement will now be added to all edges of the traced outline.
- Using a ruler, mark at close intervals, the measurement calculated in the above step.
- Join these markings to create the edge of the pattern.
- Fold the pattern in half from both directions, matching the opposite edges, to create the grain lines that you will need to lay out the pattern. Use a ruler or yardstick to draw the fold lines and keep the lines straight. A cover that is not cut out on a straight grain will want to twist out of place on the ironing board.
- Cut out the pattern piece.
03 of 08
Lay Out and Cut Out
Continue to 4 of 8 below.
- Iron your fabric and utility fabric, pressing out any fold lines.
- Lay the fabric out, in a single layer, on a flat surface.
- Place the pattern pieces down so you will be keeping either grainline parallel to the fabric selvage.
- Measure the distance of the grainline from the selvage for the length of the line to be sure it is an even distance the entire length of the line on the pattern piece.
- Pin the pattern piece in place, keeping the pattern piece smooth.
- Cut out the fabric, cutting along the edge of the pattern piece.
- Repeat for the other fabric layer.
04 of 08
Start Sewing the Ironing Board Cover
Continue to 5 of 8 below.
- Place both pieces of fabric on top of each other with the right side on top, keeping the layers smooth and aligning the edges.
- Zigzag stitch on the edge of the fabrics to join the two layers together. They will be worked as one through the rest of the directions.
- Sew a line of straight basting stitching, a half inch in from the edge.
- Press the edge under, using the stitching line as a guide. (Pressing with a pressing bar first can prevent burned fingers.)
- Press under again, the same amount, to enclose the zigzagged edge of the fabric. Use the basting stitches to ease in extra fullness, and prevent as many tucks as possible.
05 of 08
Sew Buttonholes for the Drawstring
Sewing a buttonhole doesn't translate to "panic." Use your sewing machine manual to guide you through sewing a buttonhole and practice on scrap fabric before sewing a buttonhole on your project at hand.
These buttonholes will be used for the drawstring that holds the ironing board cover in place.
Continue to 6 of 8 below.
- Find the center of the short back edge of the ironing board cover.
- Sew two, scant 1/2", long buttonholes in the inner folded edge as shown in the photo, placing them 1/2" from the center or an inch apart.
- Open the buttonholes.
06 of 08
Sew the Casing
Continue to 7 of 8 below.
- Be sure to ease in as much fullness as possible, to prevent tuck, before sewing the casing in place.
- Re-press the entire edge and pin in place.
- Sew the casing by sewing as close to the inner folded edge as possible. Using a guide on your sewing machine foot and watching the guide rather than watching your sewing machine needle and watching the guide will help you sew straight and stay on the edge of the fold.
- Sew over the first few stitches when you have come around the cover.
- Knot the end of the cord.
- Place a safety pin that will fit through the casing into the knot and secure the safety pin.
- Use the safety pin to guide the cord in a buttonhole and through the casing out the other buttonhole.
07 of 08
Padding the Ironing Board Cover
If you are replacing the entire padding, as in not using any of the padding from the previous cover, use the previous padding as a guide.
Continue to 8 of 8 below.
- Supplement the previous padding by laying the ironing board face down on the one or two layers of cotton batting and tracing the edge of the ironing board.
- Cut out the batting and place it centered with the previous batting.
08 of 08
Placing the Ironing Board Cover on the Ironing Board
- Place the ironing board cover, with the padding in place, face down, on a flat surface.
- Place the padding as centered as possible, so there is an even distance on all edges of the ironing board cover.
- Place the ironing board face down on the batting, center on the cover.
- Pull the drawstring to snug the ironing board cover.
- Use a toggle or tie the cord to hold the cover snugly in place.