How to Embroider on Leather

Embroidered leather card case
The Spruce Crafts / Mollie Johanson

Make an Embroidered Leather Case

How to Embroider Leather
Mollie Johanson

Think embroidering on leather is too difficult? Think again! With this easy tutorial, you'll soon be stitching on all your favorite leather items. You can even get started right away by making a leather card case.

Similar to embroidering on wood, the secret to hand stitching leather lies in pre-poking the holes. Once you do that, the embroidery is easy.

Gather Your Materials

Craft supplies
The Spruce Crafts / Mollie Johanson

Note: You can buy small pieces of leather at many craft supply stores or recycle an old leather item from a second-hand store. Either way should provide enough leather to make several card cases.

Cut the Leather

Leather and scissors
The Spruce Crafts / Mollie Johanson

Mark the back of the leather with cutting lines. For a card case with ample room for money and gift or credit/debit cards, start with a 4.25" x 8.5" rectangle. Use sharp scissors to cut the leather. 

Round the two corners at one end.

Fold the leather into the case formation with the non-rounded end folding in first. It should be a little over 1/3 of the way in so that when the rounded end folds over, it's not even with the opposite edge.

Mark the Pattern on the Leather

Pattern on top of leather
The Spruce Crafts / Mollie Johanson

When embroidering on leather, it helps to work with a simple pattern. The fewer holes you have to make for stitching, the easier it is. 

If you want to use the flower burst embroidery pattern shown here, be sure to download and print it at 100 percent so that it measures about 1.75" tall. 

Trace your pattern onto tracing paper and position it where you want it on the leather. In the sample, the embroidery will show on the back and wrap around to the front a little.

Use a large, sharp embroidery needle to poke through the tracing paper and the leather at each point where the needle should pass through. In this case, the stitches are detached chain stitches, so you would need a hole at the top and bottom of each petal shape.

You may find it helpful to place the leather on corrugated cardboard or cork as you do this and the following step.

Enlarge the Marked Holes

Needle and piece of leather
The Spruce Crafts / Mollie Johanson

When you remove the tracing paper, you should be able to see each of the other marked holes, however, they might be tricky to work with still. Leather often holds tight and doesn't make it easy to make these holes. 

With the tracing paper set aside, use the needle to enlarge the holes so they are easier to find as you stitch. 

You can use an awl to make larger holes, which is helpful if you want to embroider with something thicker, such as Perle cotton, but a needle works great.

Embroider Through the Leather

Stitch Through the Pre-Punched Holes
Mollie Johanson

Now it's time to start stitching!

Unless you made large holes, use three strands of embroidery floss for the best results. You can follow basic embroidery instructions for your stitching, but there are two extra tips to make this work well:

  1. Run the embroidery floss through thread conditioner to protect it as you work through the leather.
  2. Poke the needle through from the front to the back one more time before you try to find the pre-punched hole from the back. 

Measure and Mark the Holes for the Side Seams

Ruler on leather
The Spruce Crafts / Mollie Johanson

When you finish the embroidery, fold the leather into the card case shape again. Mark holes a quarter inch from the edge and from each other using a ruler and the large needle. 

Repeat this on the back of the card case and then again on the opposite edge, both front and back.

Sew the Sides of the Card Case Together

Leather side stitched
The Spruce Crafts / Mollie Johanson

To secure the sides of the card case together, stitch through the marked holes with a double running stitch. Start at the top of the opening with the first line of running stitch and then go back along the line, filling in the gaps. 

It helps to use a thread conditioner for this step as well.

Attach the Cord to the Flap

Knotted cord through the slits
The Spruce Crafts / Mollie Johanson

Cut two tiny slits in the flap of the card case, centered and parallel to the edge.

Cut a 24-inch piece of suede cord and tie a doubled knot in one end. Slide the other end through the slits in the flap, then tie a doubled knot in the other end of the cord.

Wrap the Cord Around the Case to Hold It Closed

Cord wrapped around case
Mollie Johanson

To secure the flap of the card case, wrap the cord around the case several times. Tuck the knotted end under the wrapping to hold it in place.

Use Your Card Case or Give It With a Gift Card

Embroidered leather case
The Spruce Crafts / Mollie Johanson

This case is useful for holding a little cash and a few cards. Because it's leather, it will even stretch a little over time if you want to use it to hold a lot. 

It's also a great way to present gift cards with a bit of handmade style!